Hue czajnik i express na Wifi plugin potrzebny

  • 4 Odpowiedzi
  • 2229 Wyświetleń

0 użytkowników i 1 Gość przegląda ten wątek.

*

Offline Tomasz karas

  • * 2
  • 0
    • Zobacz profil
  • Nazwa i wersja ID: Karaskot
*

Offline viperlodz

  • Moderator Globalny
  • ***** 581
  • 17
    • Zobacz profil
  • Nazwa i wersja ID: HC2 3.600 | HC2 4.080 | HC2 4.110
Odp: Hue czajnik i express na Wifi plugin potrzebny
« Odpowiedź #1 dnia: Luty 15, 2016, 02:29:41 pm »
Którą centralkę? Home Center Lite?
*

Offline Tomasz karas

  • * 2
  • 0
    • Zobacz profil
  • Nazwa i wersja ID: Karaskot
Odp: Hue czajnik i express na Wifi plugin potrzebny
« Odpowiedź #2 dnia: Luty 15, 2016, 02:32:27 pm »
Tak. Chyba ze ta droższa musi byc. Chyba ze cos polecisz
*

Offline viperlodz

  • Moderator Globalny
  • ***** 581
  • 17
    • Zobacz profil
  • Nazwa i wersja ID: HC2 3.600 | HC2 4.080 | HC2 4.110
Odp: Hue czajnik i express na Wifi plugin potrzebny
« Odpowiedź #3 dnia: Luty 15, 2016, 05:30:39 pm »
Na HCL nie ma możliwości pisania skryptów więc od razu odpada.
Co do kawy:
http://adenforshaw.com/smarter-coffee-machine-raspberry-pi-iot-coffeetime/
a dalej trzeba by poszukać;)
*

Offline andre

  • Moderator Globalny
  • ***** 197
  • 1
    • Zobacz profil
  • Nazwa i wersja ID: HC2 4.153,GRENTON, 4 x LK v2.0+OpenWRT+BLE+RPi...
Odp: Hue czajnik i express na Wifi plugin potrzebny
« Odpowiedź #4 dnia: Luty 15, 2016, 06:45:30 pm »
Dla integracji z HC 2 tutaj był opis :  http://www.fibarouk.co.uk/integrating-the-ikettle-and-sonos-on-a-fibaro-home-center-2/
Edit: znalazłem u siebie jeszcze to:
--[[

 iKettle

 This virtual device has been created by and is copyright (c) 2014, Fibaro UK Ltd
 http://www.FibaroUK.co.uk/

 You may use this virtual device for personal or commercial purposes however
 please respect our intellectual property and leave this comment block intact
 and unmodified.

]]

-- VERSION 1.1
-- change log at bottom of main loop

--[[

At the top of this page, make sure you change:
    - The IP address to that of the iKettle
    - The TCP Port to 2000

  This virtual device uses a global variable to pass status changes to other scenes
  you must create the global variable in panels->variables in order to use this feature.
  The global variable should be called 'iKettleFB'

]]

-- Only run this block of code once when we first connect to the iKettle
if not (started == 'YES') then
  started = 'YES'
 
  actionTable = {
    a0x100 = '100C selected',
    a0x95 = '95C selected',
    a0x80 = '80C selected',
    a0x65 = '65C selected',
    a0x11 = 'Warm selected',
    a0x10 = 'Warm has ended',
    a0x5 = 'Turned on',
    a0x0 = 'Turned off',
    a0x8005 = 'Warm length is 5 minutes',
    a0x8010 = 'Warm length is 10 minutes',
    a0x8020 = 'Warm length is 20 minutes',
    a0x3 = 'Reached temperature',
    a0x2 = 'Problem (boiled dry?)',
    a0x1 = 'Kettle was removed (whilst on)'
  }
 
  buffer = '' -- create an empty buffer
 
  local thismodule = fibaro:getSelfId()
  local ip = fibaro:getValue(thismodule, 'IPAddress')
  local port = fibaro:getValue(thismodule, 'TCPPort')

  tcpSocket = Net.FTcpSocket(ip, port)
  tcpSocket:setReadTimeout(1000)
  bytes, errorCode = tcpSocket:write("get sys status\n")
  fibaro:debug('Connected to iKettle')
  fibaro:log('Connected')
end

function bit(bitNum)
  return 2 ^ (bitNum - 1)
end

function hasbit(data, p)
  return data % (p + p) >= p
end

function setbit(data, p, setIt)
  if (setIt) then
    return hasbit(data, p) and data or data + p
  else
    return hasbit(data, p) and data - p or data
  end
end

function processKey(key)
  return {
    on      = hasbit(key, bit(1)),
    warm    = hasbit(key, bit(2)),
    temp65  = hasbit(key, bit(3)),
    temp80  = hasbit(key, bit(4)),
    temp95  = hasbit(key, bit(5)),
    temp100 = hasbit(key, bit(6))
    }
end

function setGV(value)
  fibaro:setGlobal('iKettleFB', value)
end

function processCommand(cmnd)
  -- a command will always start with 'sys status '
  -- so we can remove the first 11 characters.
  local action = string.sub(cmnd, 12) -- from the 12th char onwards
 
  pos = string.find(action, "key=")
  if (pos) then
    -- this is a response to a get sys status request
    state = processKey(string.byte(action, 5, -1))
    local res = ''
    if (state.on) then
      res = res .. 'On'
      setGV('0x5')
    else
      res = res .. 'Off'
      setGV('0x0')
    end
    if state.warm then
      res = res .. ' and warming'
      setGV('0x11')
    end
    if state.temp65 then
      res = res .. ' at 65 degrees'
      setGV('0x65')
    end
    if state.temp80 then
      res = res .. ' at 80 degrees'
      setGV('0x80')
    end
    if state.temp95 then
      res = res .. ' at 95 degrees'
      setGV('0x95')
    end
    if state.temp100 then
      res = res .. ' at 100 degrees'
      setGV('0x100')
    end
    return res .. '.'
  else
    --- this is an asyncronus status update
    setGV(action)
    message = actionTable['a' .. action] or action
    return message .. '.'
  end
end

function parseIt(buf)
  -- find the first occurance of 'set state '
  pos = string.find(buf, "sys status ")
  if (pos) then
    buf = string.sub(buf, pos) -- trim any junk from the beginning
    endPos = string.find(buf, '\r')
    while (endPos) do
      -- we have a potential command
      command = string.sub(buf, 1, endPos-1)
      buf = string.sub(buf, endPos + 1)
     
      local feedback = processCommand(command)
      fibaro:call(fibaro:getSelfId(), "setProperty", "ui.labStatus.value", feedback)
      fibaro:debug(feedback)
      fibaro:log(feedback)
     
      endPos = string.find(buf, '\r')
    end
  end
  return buf
end

state = tcpSocket:read()
if (tostring(state) ~= '') then
  buffer = (buffer .. state)  -- add anything we read from the socket to the buffer
  buffer = parseIt(buffer) -- process any useful stuff from the buffer and keep the leftovers
end

--[[

Change log

1.1
- Added buttons for warm on/off, 5 mins, 10 mins and 20 mins.
- Added support for HCL (no feedback)

1.0
- Initial release Buttons: [On,Off,100,95,80,65], Status - all feedback

]]
« Ostatnia zmiana: Luty 15, 2016, 06:53:38 pm wysłana przez andre »