Uceglenie Vera Lite

  • 3 Odpowiedzi
  • 4083 Wyświetleń

0 użytkowników i 1 Gość przegląda ten wątek.

*

Offline Hansolo

  • * 10
  • 0
  • Nazwa i wersja ID: Vera Lite
Uceglenie Vera Lite
« dnia: Październik 24, 2016, 06:49:06 pm »
Witam. Przy aktualizacji softu coś poszło nie tak.
Mam teraz cegłę.
Próbowałem zrobić to jak http://wiki.micasaverde.com/index.php/Firmware_Flash_VeraLite lecz niestety po uruchomieniu programu recovery nie widzi centralki.
Mam okno wyboru karty sieciowej na której nic nie ma.
Oczywiście wszystko zrobione krok po kroku.
Jakieś sugestie?
*

Offline Sierek

  • *** 102
  • 4
  • Nazwa i wersja ID: Vera Lite, Vera Plus, HA na HP620t
Odp: Uceglenie Vera Lite
« Odpowiedź #1 dnia: Październik 25, 2016, 06:22:49 pm »
Miałem ten sam problem. Dwa razy ucegliłem Verę. Dostałem z Helpdesku poradę bez programu recovery. Za którymś razem Vera zaskoczyła, co ciekawe ze zaktualizowanym softem.
Cytuj
Hi Jacek,
Can you please try and reset the unit back to factory defaults by pressing the reset button for 30 seconds using a paperclip or something similar?
After the reset, you will need to wait up to 15-20 minutes for the unit to come back.
If after 15-20 minutes the unit is still not back on, you will need to follow the steps from the file that I’ve attached to this e-mail in order to restore your unit.
Please let me know how it went and if necessary I will get back at you.
Have a wonderful day
Regards,

How To restore Vera lite
1. Connect your computer directly into the LAN port on the Vera lite unit
2. Put a static IP on your computer (192.168.1.2) and the gateway 192.168.1.1 . You Can find
more information about it at step 8.
3. Plug the power adapter in Vera and when the blue light starts blinking, press and release
the reset button
4. Open a command prompt and telnet into the unit: telnet 192.168.1.1
Run these commands:
flash_eraseall -j /dev/mtd7
sync
echo b > /proc/sysrq-trigger
Note 1: If you cannot telnet to the unit you will need to install the telnet client. Windows 7 :
From Control Panel > Programs and Features > Turn Windows Feature On or Off >and check
the Telnet Client box to install it .
Note 2: OR you can download 'Putty' to Telnet to the unit. For 'Host name' type 192.168.1.1
and for 'Connection Type' select Telnet. Then hit Open.
Now the Vera unit should reboot and you should see it booting up. It might take a couple of
seconds, first the LED should be solid red, then green, red and after that it should boot up
6. Change your IP address back on automatically or 192.168.81.2 and gateway 192.168.81.1
7. Check that the Dashboard loads on 192.168.81.1 after all the LEDs are on and solid
8. How to set a Static IP to your computer.
In Windows 7
Open Control Panel
View by: Large icons -> Network and Sharing Center
View by: Category -> View netork status and tasks
Click on Change adapter settings
Right click on LAN connection to Vera , then click on Properties
Highlight the Internet Protocol Version 4 (TCP/IPv4) item, and click on Properties
In the IP address field enter 192.168.1.2
In the subnet mask field enter 255.255.255.0
In the Default gateway field enter 192.168.1.1
Click OK
Click OK Again
In Windows XP
Open Windows Start menu.
Open Control Panel.
Classic view: Open Network Connections
Category view: Select Network and Internet Connections, and then Network Connections.
Double-click on your the LAN connection to Vera.
Click Properties.
In the General tab, highlight the Internet Protocol (TCP/IP) item, and click Properties.
In the IP address field enter 192.168.1.2
In the subnet mask field enter 255.255.255.0
In the Default gateway field enter 192.168.1.1
Click OK
Click OK again
In Mac OS X
Open the Apple Menu(Top left corner of your screen)
Click System Preferences
Click Network
Click the Locations dropdown and select Edit Locations
Click the plus sign and call your new location "Vera system Troubleshooting"
Select "Ethernet" from the list on the left
Select "Manually" from the Configure IPv4 dropdown
Enter 192.168.1.2 in the IP address field
Enter 255.255.255.0 in the subnet mask field
Enter 192.168.1.1 in the Router field
Hit "Apply"
*

Offline Hansolo

  • * 10
  • 0
  • Nazwa i wersja ID: Vera Lite
Odp: Uceglenie Vera Lite
« Odpowiedź #2 dnia: Październik 27, 2016, 08:02:29 am »
Też to mam.
Ale po wpisaniu 1 polecanie prosi mnie o login i hasło.
*

Offline Hansolo

  • * 10
  • 0
  • Nazwa i wersja ID: Vera Lite
Odp: Uceglenie Vera Lite
« Odpowiedź #3 dnia: Październik 28, 2016, 09:16:41 am »
Mój błąd. Miałem włączone Wi-Fi i próbował się połączyć z czymś innym.
Niestety nadal mam problem bo po wpisaniu ostatniego połączenia, Vera się resetuje, ale mimo to nadal nie działa.
Palą się nadal te same diody, czyli niebieska 1 i pomarańczowa 3.